User Manual MG3900

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

You can find the model number on the back of your product.

The full model number (e.g. MG1234/56) is located on the bottom of the packaging, your receipt or order confirmation.

Never rinse the handle under the tap or immerse it in water. Only the cutting element and the attachments can be rinsed under the tap when detached from the handle.

Getting the handle wet may cause irreversible damage to your appliance. This will result in the appliance becoming unusable.

• This appliance can only be used without cord.

• Switch off the appliance before removing or attaching attachments and before cleaning.

• Clean the appliance after each use.

1. Nose and ear hair trimmer

2. Cutting element

3. On/off button

4. Charge indicator

5. Socket for small plug

6. USB cable

7. Note:The power source is not included. A suitable power source (e.g. Philips HQ87) is available via www.philips.com/support.

8. Cleaning brush

9. Stubble comb 1 mm

10. Stubble comb 2 mm (only with models MG3930, MG3935, MG3940, MG3945, MG3946)

11. Beard comb 3 mm (only with models MG3915, MG3920)

12. Beard comb 5 mm (only with models MG3915, MG3920)

13. Beard comb 7 mm (only with model MG3920)

14. Adjustable trimming comb 3 mm – 7 mm (only with models MG3930, MG3935, MG3940, MG3945, MG3946)

15. Hair comb 9 mm (only with models MG3935, MG3945)

16. Hair comb 12 mm (only with models MG3915, MG3920, MG3930, MG3940, MG3945, MG3946)

17. Hair comb 16 mm (only with models MG3930, MG3940, MG3946)

18. Body comb 3 mm (only with models MG3935, MG3940, MG3945, MG3946)

19. Intimate comb 1 mm (only with models MG3945, MG3946)

Not shown:pouch

Caution

• Charging or using the appliance at temperatures below 10 °C or higher than 35 °C adversely affects the lifespan of the battery.

• If the appliance is subjected to a major change in temperature, pressure or humidity, let the appliance acclimatize for 30 minutes before use.

• The USB supply unit is not included. To safely charge your product, only use a certified supply unit with output rating 5 V, ≥ 1.

Charge the appliance before first use and when the motor starts working more slowly.

Warning: Keep the USB cable and the USB supply unit dry.

1. Make sure the appliance is switched off.

2. 

3. Insert the small plug of the USB cable into the socket in the bottom of the appliance.

4. 

5. Insert the USB plug into the USB supply unit (not provided).

6. 

7. Insert the USB supply unit into the wall socket.

8. After charging, remove the USB supply unit from the wall socket and pull the small plug out of the appliance.

Always check the product and all accessories before you use it. Do not use the product or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.

Because of hygiene, only one person should use the product.

Trimming tips

Trimming tips

• When trimming for the first time, start by using the comb with the maximum trimming length setting to familiarize yourself with the appliance.

• Since all hairs do not grow in the same direction, you may want to try different trimming directions (i.e. upwards, downwards, or across). Practice is best for optimum results.

• Always make smooth and gentle movements and be sure the surface of the comb always stays in contact with your skin.

• For best results, use the appliance on clean, dry hair, as wet hair tends to stick to the body.

• When too many hairs have accumulated on the appliance, remove the hairs before and/or during use, for best trimming results.

Detaching and attaching cutting elements

1. 

2. To detach a cutting element, place your thumb below the teeth of the cutting element and gently push upwards until the cutting element comes off the handle.

3. 

4. To attach a cutting element, insert the plastic notch at the back of the cutting element into the guiding slot in the handle. Then gently press the teeth of the cutting element downwards until the cutting element clicks into place.

Detaching the nose and ear hair trimmer

1. Place your finger on the recess at the back of the attachment and push the attachment off the handle. Use your other hand to prevent the attachment from dropping on the floor.

Detaching and attaching guards

1. 

2. To attach any type of comb onto the cutting element,slide the front part of the comb onto the teeth and press the notch at the back of the comb downwards until it clicks into place.

3. 

4. To detach any type of comb from the cutting element, carefully push its back part off the appliance and then slide it off the cutting element.

To switch the appliance on or off, press the on/off button once.

Tip

Always comb your beard or moustache with a fine comb before you start trimming.

Beard guards MG7790, MG7750, MG 5790, MG5760, MG5750

Use a stubble or beard comb attached to the cutting element to trim your beard and mustache evenly. The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a stubble or beard comb to the cutting element.

2. 

3. To trim in the most effective way, move the comb against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

4. Switch off and clean the appliance after each use.

Full-size hair trimmer

Use the cutting element without any comb to trim hair close to the skin (to a length of ca. 0.5 mm) or to create clean lines around your beard, neck and sideburns.

1. To trim hair close to the skin, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth.

2. 

3. For contouring, hold the cutting element perpendicular to the skin and move it upwards or downwards with gentle pressure.

4. Switch off and clean the appliance after each use.

Use the adjustable beard and hair comb to trim your beard or scalp hair evenly to the desired length. The hair length settings range from 3 mm to 7 mm and relate to the number of millimeters of hair length that will remain after trimming.

1. Attach the adjustable beard and hair comb to the cutting element.

2. 

3. Use the slide switch on the comb to adjust the length.

4. To trim in the most effective way, move the comb against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

5. Switch off and clean the appliance after each use.

Hair clipping tips

Always comb your hair before you start trimming.

For best results, use the appliance on clean, dry hair.

Hair guards

Use a hair comb attached to the cutting element to evenly trim the hairs on your head.The numbers on the combs relate to the number of millimeters of hair length that will remain after trimming.

1. Attach a hair comb to the cutting element.

2. 

3. Move the appliance slowly over the crown from different directions to achieve an even result. Always move the appliance against the direction of hair growth. Press lightly. Make sure that the surface of the comb always stays in contact with the skin.

4. Make overlapping passes over the head to ensure that all hair that should be cut has been cut.

5. Gently shake the hairs off the appliance in between strokes to prevent hairs from collecting between the cutting element and the comb.

6. Switch off and clean the appliance after each use.

Important

Always use a body comb when trimming sensitive areas.

Attach the intimate comb to the cutting element to trim hair on sensitive body areas (such as your intimate area, armpits or chest) to a short length (1 mm), for extra skin protection.

1. Attach the intimate comb to the cutting element.

2. If possible, stretch a small area of the skin with two fingers to make the hairs stand upright.

3. 

4. Place the flat side of the cutting element against your skin and make strokes against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

5. Switch off and clean the appliance after each use.

Body combs MG7750

Attach the body comb to the cutting element to trim hairs below the neckline to the length of 3 mm.

1. Attach the body comb to the cutting element.

2. 

3. To trim in the most effective way, stretch the skin with your free hand and move the comb against the direction of hair growth. Make sure that the surface of the comb always stays in contact with the skin.

4. Switch off and clean the appliance after each use.

Nose trimmer

Use the nose and ear hair trimmer to trim your nose and/or ear hair.

• Make sure nasal passages are clean. Make sure outer ear channels are clean and free from wax.

• Do not insert the cutting element too deep into your nostrils or ear channels (max. 5 mm).

• When trimming both nose and ear hair, make firm, rotary movements to ensure that the cutting element reaches all the hairs.

• Clean the nose and ear hair trimmer after each use.

Note: The nose and ear hair trimmer is not designed to clean-shave your nostrils or ear canals, but to cut the hairs to a shorter length. Nose and ear hairs have important protective functions and should not be fully removed.

Trimming nose hair

1. 

2. Gently insert the cutting element into one of the nostrils. Move the tip in and out of the nostril in a firm, rotary motion to cut the hairs to a shorter length.

Trimming ear hair

1. Slowly move the cutting element along the outer ear to trim hairs that stick out beyond the rim.

2. 

3. Gently insert the cutting element into the outer ear canal. Move the tip in and out of the outer ear canal in a firm, rotary motion to cut the hairs to a shorter length.

Switch off and clean the product after each use.

Never rinse the handle under the tap or immerse it in water. Only the cutting element and the attachments can be rinsed under the tap when detached from the handle.

Switch off the appliance before removing or attaching attachments and before cleaning.

Only use cold or lukewarm water to clean the cutting element and the attachments.

Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

Never dry the cutting element with a towel or tissue, as they may get caught in the teeth and cause damage.

1. Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.

2. Wipe the handle with a dry cloth.

Cleaning with brush

1. Detach any comb from the appliance and clean it with the cleaning brush.

2. 

3. Detach the cutting element from the appliance. Clean the teeth and the inside of the cutting element with the cleaning brush.

4. 

5. Clean the inside of the hair chamber with the cleaning brush.

6. Keep the handle away from water. Make sure that no water reaches the inside of the hair chamber.

Cleaning attachments under the tap

1. 

2. Detach any comb and the cutting element from the appliance and rinse them under the tap.

3. 

4. Carefully shake off excess water and let the parts air-dry completely before reattaching them to the appliance.

Cleaning the nose and ear hair trimmer

Clean the nose and ear hair trimmer immediately after use and when a lot of hair or dirt has accumulated on the cutting element.

1. Detach the nose and ear hair trimmer from the product.

2. 

3. Rinse the nose and ear hair trimmer head under running tap water.

4. For a thorough clean, immerse the nose and ear hair trimmer head in a bowl with warm water for a few minutes to soak and soften the debris. Then rinse the nose and ear trimmer head under running tap water to remove stubborn debris.

5. Carefully shake off excess water and let all parts air-dry completely before reattaching them to the product.

Note: Do not place or store the appliance where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

• Make sure that the appliance is switched off and that the USB power source has been removed from the power outlet and from the appliance.

• Do not wrap the USB cable around the appliance when storing.

• Store the appliance, the USB power source and all the accessories in the pouch supplied, if provided with your appliance. Attach a comb to the cutting element to protect the teeth during storage.

• Place the pouch in a safe, dry location, where it will not be crushed, banged, or subject to damage.

• Make sure that the appliance and the accessories are dry before you place them in the pouch.

For all product support, power consumption details and the EU Declaration of Conformity, please visit www.philips.com/support.

Cutting units are not covered by the terms of the international warranty because they are subject to wear.

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

• 

• This symbol means that electrical products and batteries shall not be disposed of with normal household waste.

• Follow your country’s rules for the separate collection of electrical products and batteries.